Aim-TTI LD400P Electronic DC Load, 80V, 80A, 400W with analogue and digital control, USB, RS232, LAN (LXI) and GPIB
LD400 Series>
- Versatile solution for testing dc power sources
- Constant current, resistance, conductance, voltage and power modes
- Wide voltage and current range, 0 to 80V and 0 to 80A
- 400 watts continuous dissipation at 28oC (360W at 40oC)
- 600 watts short-term dissipation (up to 60 seconds)
- Low minimum operating voltage of <1V at 40A
- High resolution and accuracy for level setting
- Built-in transient generator with variable slew
- Current monitor output for waveform viewing
- Variable drop-out voltage for battery testing
- High resolution backlit graphic LCD with soft key control
- Analogue remote control of levels and TTL control of on/off and transient switching
- Front and rear input terminals (front terminals 30A max.)
- Full bus control via USB, RS232, GPIB and LXI compliant LAN interfaces (LD400P)
Az egyes termékeknél feltüntetett leírások tájékoztató jellegűek. A H TEST a.s. nem vállal felelősséget a www.htest.hu és eshop.htest.hu oldalon lévő, esetlegesen előforduló hibákért, valamint pontatlanságokért – melyekért szíves elnézésüket kérjük. Pontos, részletes és érvényes leírások az adott termék/műszaki adatlapján találhatók, mely a gyártók honlapjáról tölthetők le. Részletes információk
| nettó ár | € 1 604,00 |
| bruttó ár | € 2 037,08 |
| Elérhetőség | Kérésre |
| Termékkód | AIM-TTI_LD400P |
Szavatosság 36 hónap
Részletes leírás Aim-TTI LD400P Electronic DC Load, 80V, 80A, 400W with analogue and digital control, USB, RS232, LAN (LXI) and GPIB
The LD400 is an inexpensive electronic load which is suitable for testing and characterising a wide variety of dc power sources. It can be used to investigate the behaviour of many different types of power source such as batteries and solar cells, as well as electronic power supply units. Its wide voltage/current range, multiple operating modes and builtin transient generator give it the versatility to offer test solutions from the design laboratory through to the component test area. The LD400P adds full bus remote control via USB, RS-232, GPIB and LAN (Ethernet) interfaces..
The LD400 can operate at voltages below 500mV for currents up to 10 amps. At higher currents the fixed minimum resistance (typically better than 25mW) gradually raises the minimum operating voltage, but it remains below 1 volt up to 40 amps and below 2 volts up to 80 amps. This low operating voltage allows it to be used for many low voltage applications for which other electronic loads are unsuitable.
The LD400 incorporates a full variable frequency, variable duty cycle transient generator. Switching between the two preset levels can be done at any frequency between 0.01Hz and 10kHz. The transient generator can be used in all operating modes. The rate of change between levels (slew rate) is controllable over a wide range.
Videók és letöltések Aim-TTI LD400P Electronic DC Load, 80V, 80A, 400W with analogue and digital control, USB, RS232, LAN (LXI) and GPIB
Típus: pdfA termék a következő kategóriában szerepel
Tartozékok Aim-TTI LD400P Electronic DC Load, 80V, 80A, 400W with analogue and digital control, USB, RS232, LAN (LXI) and GPIB
Kapcsolódó termékek Aim-TTI LD400P Electronic DC Load, 80V, 80A, 400W with analogue and digital control, USB, RS232, LAN (LXI) and GPIB
Kiegészítő tartalom
Ajánlatunk
Kapcsolat
 |
H TEST Hungary Kft. Koroknay Gyula utca 9. 9027, Győr |
 |
+36 96 999 262 |
 |
info(at)htest.hu |